Get a free quote

Free calculator

Tile layout calculator: setting out the floor

Type the room size, the tile and the joint, and see the width of the cut tiles at each wall for three ways of starting, drawn on a plan, with the best one picked for you.

Setting-out calculatorCuts at the walls for three starts

1The room

2The tile

Shaded tiles are cuts. Dashed lines are the room's centre lines.

Along the length

StartCut at wallsTiles

Across the width

StartCut at wallsTiles

Before laying a single tile, a good tiler sets out the floor: works out where the joints will fall so the cut tiles at the walls are equal on both sides and not thin slivers that crack and look like a mistake. This calculator does that sum for both directions of the room.

Three ways to start

  • From a wall: a full tile against one wall and whatever is left at the opposite wall. Quick, and fine when the far wall is hidden under cupboards.
  • Joint on the centre line: a grout joint runs down the middle of the room, so the cuts at both walls are the same width.
  • Tile on the centre line: a tile sits in the middle of the room, which moves the cuts by half a tile. If the centre joint leaves thin cuts, this fixes them.

The calculator works out all three in each direction and picks the one with the widest cut, aiming for at least a third of a tile and ideally half. It leaves a gap at each wall for movement, which the skirting covers.

Setting out on site

Find the middle of two opposite walls and snap a chalk line between them, then a second line at right angles using the 3, 4, 5 rule: 3 m along one line, 4 m along the other, and the diagonal between those points must be exactly 5 m. Dry-lay a row of tiles with spacers along each line to check the cuts at the walls before mixing any adhesive. Where the room is not square, keep the line parallel to the wall you see most, usually the one opposite the door.

When the room is open-plan

Centre the layout on what the eye sees first: the front door, a sliding door to the patio, a fireplace or the kitchen island. In passages, centre the tiles on the passage width so both walls have the same cut. Plank tiles look best laid along the longest view, with the joints staggered by no more than a third of the plank length to avoid lipping.

Frequently asked questions

Where should I start tiling a floor?
Usually in the middle of the room on a chalk line, working back towards the door, so the cuts at opposite walls are equal. Start at a wall only when one side is hidden, or the wall is the one you see most and you want full tiles along it.
What is the smallest cut tile I should have?
Aim for at least half a tile, and no less than a third. Thin slivers are hard to cut, break easily, and draw the eye to the wall. Moving the layout by half a tile usually fixes it.
How wide should the gap at the wall be?
About 5 mm indoors and 8 to 10 mm on large or outdoor floors, left empty or filled with a flexible sealant and covered by the skirting. Tiles grouted tight to the wall have nowhere to move and can lift.
Does the layout change the number of tiles?
A little. Centring can mean one more row of cut tiles. The tile calculator adds 10% for cuts, which covers this for most rooms.

More calculators

Get a free tiling quote

Draw the room, pick the tile, and tell us where you are. Tile suppliers and tilers who work in your area quote you directly.

Setting-out planSent to tile suppliers and tilers near you

1The job

2The room (the plan counts the tiles)

Type the length and width to draw the room
Area
-
Tiles incl. cuts
-
Boxes
-
Adhesive, 20 kg
-
Grout, 5 kg
-
Rough price
-

Shaded tiles along the edges are cut tiles.

3Where and when

Rooms and areas

4Request list (optional)

  1. 01
  2. 02
Up to 12 lines: tiles, materials or work.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable tile suppliers, flooring companies or tilers. See our privacy policy.

Get a free tiling quote