Get a free quote

Free calculator

Screed and self-levelling calculator

Type the area and the average depth, and see the bags of self-levelling compound, or the cement and sand for a screed, plus the primer.

Levelling calculatorSelf-levelling or sand and cement

1The floor

2The product

-

bags

Material
-
-
-
-
-
Dry before tiling
-

Large tiles and vinyl need a flat floor: no more than about 3 mm of dip under a 2 m straight edge. Thin dips are filled with self-levelling compound, which you pour and spread; deeper or sloping floors get a sand and cement screed. This calculator turns the area and depth into bags.

Self-levelling compound

Self-levelling compound uses about 1.6 to 1.8 kg of powder per m² for every millimetre of depth. A 20 kg bag therefore covers roughly 4 m² at 3 mm, or 2.4 m² at 5 mm. Most products work from about 2 to 10 mm in one pour, some to 30 mm. Prime the floor first, usually about 0.15 litres per m², so the compound does not dry out too fast and crack. Mix whole bags at a time and pour in strips, working fast; it sets in 20 to 30 minutes and can take foot traffic in a few hours.

Sand and cement screed

A tile screed is usually one part cement to four parts sharp (plaster or river) sand, mixed fairly dry, at 25 to 50 mm thick on a concrete slab, or 50 to 75 mm when it floats on insulation or underfloor heating. Because a dry mix packs down, you need about a third more dry material than the screed's volume: per cubic metre of screed, roughly 7 to 8 bags of 50 kg cement and just over 1 m³ of sand. The calculator uses these figures. A new screed should dry for about a week per 25 mm before tiling.

Finding the average depth

Lay a long straight edge or a laser line across the floor in a few directions and measure the gaps at the low spots. The average depth is roughly half the deepest dip for a floor that dips evenly, or measure a grid of points and average them. Falls to a drain in a shower or on a balcony are built into the screed, usually about 1 in 80 to 1 in 100.

Frequently asked questions

How many bags of self-levelling do I need?
Multiply the area by the depth in millimetres and by 1.7 to get kilograms, then divide by the bag weight. For 20 m² at 4 mm: 20 x 4 x 1.7 = 136 kg, or seven 20 kg bags. Add a bag for losses.
Can I tile straight onto self-levelling compound?
Yes, once it is dry, usually after one to three days depending on the depth and product. Use the primer and adhesive the maker recommends, especially under large format tiles.
How thick should a screed be under tiles?
At least 25 mm bonded to a concrete slab, and 50 to 75 mm when it is laid over insulation, plastic or underfloor heating. Thinner screeds crack and sound hollow.
Do I need to level the floor before tiling?
For 300 to 450 mm tiles, adhesive can take up small dips. For 600 x 600 and larger, wood-look planks and vinyl, the floor must be flat, or the tiles lip at the edges and can pop. Ask the tiler to check with a straight edge.

More calculators

Get a free tiling quote

Draw the room, pick the tile, and tell us where you are. Tile suppliers and tilers who work in your area quote you directly.

Setting-out planSent to tile suppliers and tilers near you

1The job

2The room (the plan counts the tiles)

Type the length and width to draw the room
Area
-
Tiles incl. cuts
-
Boxes
-
Adhesive, 20 kg
-
Grout, 5 kg
-
Rough price
-

Shaded tiles along the edges are cut tiles.

3Where and when

Rooms and areas

4Request list (optional)

  1. 01
  2. 02
Up to 12 lines: tiles, materials or work.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable tile suppliers, flooring companies or tilers. See our privacy policy.

Get a free tiling quote